|
Molecular Sieve Bat tery | Purifying
mass & L K Mixture | Distribution
Panel | Water
Pump |
WeighingScale|
| Oxy / Nitr Cylinder
trolley | Water
Softner Plant | Compressor
for Dissolved Acetylene | Cooling
Tower |
| Acetone Pump
| Valves
| LG Cylinders
| Vaporizers
| Analysers
|
Gas Compressors |
| Cylinder Testing
Equipments |
Futuristic Control Panel |
Besides manufacture and export of Oxygen / Nitrogen
plants, Acetylene Plants and Nitrous Oxide plants, we
can also supply you with the following ancillaries.
Tailor made items can be offered to suit specific requirements.
 |
Sanghi-Molecular
Sieve Battery:
To remove moisture, Carbon-di-oxide & traces
of Acetylene and other hydrocarbons consisting
of 2 dries filled with molecular sieve along with
regenating electric heater. Temperature sensors
& control panel with temperature controller.
Each vessel of Molecular Battery is filled with
molecular sieve of 1.5/3 mm type 13-X. This is
regenerative type capacity 400m3/hr to 2000 m3/hr
and 12 hour regeneration cycle. |
Sanghi-Purifying
mass & L K Mixture:
A mixture of purifying mass & L K Mixture is used
to remove unpurities such as Sulphur, Phosphorus, Arsenic,
Ammonia etc. in the form of hydrides such as Hydrogen
sulphide, Phosphine etc. This chemical is regnerative,
can be used for several applications.
 |
Sanghi-Distribution
Panel For Oxygen / Nitrogen Plants:
This is a free standing, non-compartmentalised
Structure housing the starter feeders for all
the drives required for the Acetylene Plant /
Oxygen plant and is fabricated out of CRCA steel
& is surface treated to international quality
standards. It has a front opening and has adequate
cabling space. The panel is dust-proofed using
double-lipped Neoprene rubber gaskets. The door
hinges are concealed and have a back-up channel
to ensure proper dust-proofing. The wiring is
done with black PVC insulated stranded Copper
wires & the wire terminations are identified
with PVC ferrules. |
Sanghi
– Valves for cylinders:
 |
 |
|
Oxygen / Nitrogen / Acetylene / Argon Cylinder
valves with SS304 spindle & Teflon. This cylinder
valve is fixed to a gas cylinder by screwing &
its essential functions.
To enable filling of gas into the cylinder.
To ensure proper storage of the gas inside the
gas cylinder.
To release the gas as and when required.
To act as a safety device for the cylinder if
valves are provided with safety. |
| Sanghi-Water
Pump:
The centrifugal Monoblock pump is of close grained
cast iron construction. A statically balanced
impeller is fitted to give maximum output at low
running cost. RPM 2880; 3.0 H.P.; Power Supply
3Ph; 50 cys; 400 / 440 Volt; A.C. Supply capacity. |
 |
 |
Sanghi-Weighing
Scale:
Dial Scale 3205 CLE / COE Capacities: - 100, 200,
300, 500 & 1000 Kg. White pointer with black
indicator to give shadowless line-to-line (non-parallax)
indication on 584 mm dia. Ready line . Scale mounted
on four wheels enclosed in a substantial cast
iron frame. Tough, dust proof and moisture proof
housing to stand up to any conditions. This ensures
no rusting and no deterioration of the mechanism
components. |
| Sanghi-Oxy
/ Nitr Cylinder trolley:
A battery of cylinder mounted on a trolley with
wheels that can be transported and used where
the consumption of the gas is more. These mounted
cylinders are interconnected with individual isolation
valves with pressure gauge. This product will
immensely help in saving transportation cost and
cylinder handling. |
 |
 |
Sanghi
Water Softner Plant:
Custom built water softner plants with flow Capacities
ranging from 0.7m3 / Hr to 12m3 / hr with an output
per regneration ranging from 8.1m3 to 203m3 max.
working pressure 3.0kg / cm2. |
Sanghi-Compressor
for Dissolved Acetylene:
This is used for filling of the cylinders a reciprocating,
oil lubricated, multi-stage, water submerged compressor
with intercoolers, safety relief valve for each
stage, driven by a 15 HP. Flame proof. |
 |
 |
Sanghi-Cooling
Tower:
Induced draft Rotary sprinklers in FRP casings
with electric motor 3 HP / 960RPM with or without
basin in different capacities from 500 LPM to
1000 LPM. |
| Sanghi
–Acetone Pump:
It is a geared motor pump coupled with motor by
love-joy coupling. The pump has two parts mainly
suction port and the discharge port. The suction
port is provided with extended pipe and foot value
to reach the bottom of the acetone drum. |
 |
 |
Liquid
Gas Cylinders
LGC's are small liquid cylinders with in built
pressure building & evaporating coil to allow
both gas as well as liquid withdrawal. It can
be transported to & from customers site with
liquid filled in just like high pressure gas cylinder.
This facilitates larger quantity of product transfer
in liquid form than in Gaseous form. It is ideal
for Liquid N2, Oxygen, Argon CO2 & N2O.
|
| Vaporizers:
High Pressure Atmospheric Vaporizer for LOX/LIN
Design.
Construction of Tubes : Copper
Construction of Frame : Mild Steel
Operating Pressure & Design Pressure will
vary depending upon the users requirement. However,
the Vaporizers from operating pressure of 8 Kg/cm2g
to 200 Kg/cm2g are available.
The Vaporizers are used for converting the liquid
form of product (i.e. O2,N2,Argon) to the gaseous
form. This transformed gas can be supplied in
pipe line through Low Pressure Vaporizer or can
be filled in cylinders through High Pressure Vaporizers
.
|
 |
 |
Analysers
We offer online, digital, electronic analysers
with mounting & portable type for monitoring
purities of Oxygen, Nitrogen, Argon and other
gases. This indicator is a convenient and handy
instrument for field applications where a quick,
easy and accurate measurement of oxygen is required.
The sensor being located within the instrument
requires the gas sample to be delivered to inlet
port. This instrument is ideal where the sample
is available at a slight positive pressure.
|
| Gas
Compressors
This is a reciprocating machine, with crank gear,
piston rod, piston, cylinders. The machine is
used for building up pressure of Oxygen, Nitrogen,
Nitrous Oxide gas for filling the gas into Cylinders.
These are available in various capacities and
consist of following :
Control Panel consisting of Pressure Gauge for
All the Stages and Oil Pressure, and manual unloading
Valves, Gas Coolers after all the three stages,
Safety Valves for all the three stages, N.R.V.
at Delivery, Belt Guard, Tool Box, Flywheel, Fiber
Buckets for all the three stages, Motor Pulley.
|
 |
|
|
Cylinder
Testing Equipments
The cylinders testing equipment is necessary in
the bottling plant, as the cylinders used for
filling Gas needs to be tested periodically. This
consists of the following:
Hydraulic Pump, Cylinder Vice, Cylinder Rack,
Cylinder Drier with Blower and Heater, Control
Panel Stretch Board with Glass and Brass Tubes,
Pressure Gauges Connecting Pipes, Spanners and
Tools, DOL Starter, Low Voltage Lamp for Internal
Viewing of Cylinder.
|
| |
| Futuristic
Control Panel
This futuristic and advanced control panel of
the Air separation unit can be located in an air-conditioned
room to operate and control various plant parameters.
It has been ergonomically designed for ease of
operation and for fine tuning of plant parameters
from a remote location. This panel has unique
features with digital display, indicator lamps
and instrumentation for indicating pressures and
temperatures of all stages of Air compressors.
It also has on-line digital electronic analysers
for displaying and monitoring purity of gaseous
oxygen, ultra high purity nitrogen and waste nitrogen.
It also indicates ampere ratings of all motors
used in the plant. |
|
|
